Silicon based Rubber Lubricant
|
10g calibration weight for checking
digital scales.
|
Precise digital scale measures 0 - 300g
with a resolution of 0.01g.
A necessary tool for indoor rubber power.
|
Laser-cut Hard Teflon Thrust Washers, 6 off
Size #00 - 3/32" OD for 0.010-0.015" shaft
|
Hanger loop for 1/8" motor sticks, nose button for 0.020" prop shaft. Three sets included. Glue hanger loop to motor stick with CA.
This allows you to easily change out prop and shaft assembly on your stick models.
|
Hanger loop for 1/8" motor sticks, nose button for 0.026" prop shaft. Three sets included. Glue hanger loop to motor stick with CA.
This allows you to easily change out prop and shaft assembly on your stick models.
|
Hanger loop for 1/8" motor sticks, nose button for 0.032" prop shaft. Three sets included. Glue hanger loop to motor stick with CA.
This allows you to easily change out prop and shaft assembly on your stick models.
|
Hanger loop for 1/8" motor sticks, nose button for 0.020" prop shaft, prop hub for 1.0mm carbon rods and two thrust washers. Prop shaft and carbon rods not included.
|
Hanger loop for 1/8" motor sticks, nose button for 0.026" prop shaft, prop hub for 1.0mm carbon rods and two thrust washers. Prop shaft and carbon rods not included.
|
Hanger loop for 1/8" motor sticks, nose button for 0.032" prop shaft, prop hub for 1.0mm carbon rods and two thrust washers. Prop shaft and carbon rods not included.
|
Torque meter kit, Carbon Fiber body tube, swivels to align with rubber. Approximate range 0 - 2 oz-in (0.014 N-m), suitable for up to 1 loop of 1/8" Super Sport.
|
Winder Box allows the student to set the winder down with a fully wound motor, leaving both hands free to transfer motor to the model. Key hole mount, simply use 1 pan head screw. Winder sold seperately.
|
Winder Box allows the student to set the winder down with a fully wound motor, leaving both hands free to transfer motor to the model. Key hole mount, simply use 1 pan head screw. Winder sold seperately.
|
Laser-cut Hard Teflon Thrust Washers, 6 off
Size #0 - 1/8" OD for 0.020" shaft
|
Laser-cut Hard Teflon Thrust Washers, 6 off
Size #1 - 1/8" OD for 1/32" shaft
|
6 off - 1/4" OD - 1/8" ID (No. 6) Buta-N O-Rings
|
6 off - #4 Buta-N O-Rings
|
6 off - 15/64" OD - 7/64" ID (No. 5) Buta-N O-Rings
|
Traditional boiled green soap and glycerene lube.
|
1/4" wide masking tape - 60yd roll
color may vary according to availability
|
Measures pitch in inches at 70% radius for 5 1/2" props on prop hanger or bare shaft.
|
Measures pitch in inches at 70% radius for 6" props on prop hanger or bare shaft.
|
Laser-cut Hard Teflon Thrust Washers, 6 off
Size #2 - 3/16" OD for 3/64" shaft
|
Used to increase the pitch of commercial rubber power plastic props. Push prop down wedge cutout and let it cold flow, or heat gently in a very cool oven for a few mins.
|
Laser-cut Hard Teflon Thrust Washers, 6 off
Size #3 - 7/32" OD for 1/16" shaft
|
Measures pitch in inches at 70% radius for 7" props on prop hanger or bare shaft.
|
Laser-cut Hard Teflon Thrust Washers, 6 off
Size #4 - 1/4" OD for 1/16"- 5/64" shafts
|
6mm OD, 2mm ID, ~3mm thick. Fits 1/32" prop shafts.
Hardened steel end caps with 6 balls in brass cage.
|
6mm OD, 2mm ID, ~3mm thick. Fits 3/64" prop shafts.
Hardened steel end caps with 6 balls in brass cage.
|
6mm OD, 2mm ID, ~3mm thick. Fits 1/16" prop shafts.
Hardened steel end caps with 6 balls in brass cage.
|