Pair of 7.5mm OD carbon tubes 23" long. Use to build wing on, align fuselage building jigs and other jigs with alignment hole.
|
Pack of 50 0.25" x 0.10" high power rare earth magnets. Use for magnetic building jig system or as cowl/hatch retainers in your model.
|
Pack of 16 0.25" x 0.10" high power rare earth magnets.
|
Set of 16 fuselage jig supports, one each 1/8"....2" wide in steps of 1/8". Forks are 2" high. Laser cut from birch plywood. Use with 7.5mm OD carbon rod and/or magnets, both sold separately.
|
Individual fuselage supports, please specify width required in notes field at checkout.
Available in step of 1/16" from 1/8" - 2" wide. Forks are 2" high.
|
Big adjustable fuselage support, sold individually.
Adjusts from 1 1/2" to over 4 1/2" wide. Forks are 5" high. 7.5mm Carbon rod and magnets sold separately.
|
Unique tool rides on 7.5mm carbon rod used in your fuselage jig, and provides a 10" wide perpendicular ruler graduated in 1/8" from -5" to +5". Very useful for setting up wing and stabilizer square to fuselage.
|
Used to square up root rib when building wings on 7.5mm carbon rods. Laser cut from birch plywood.
|
Pack of four hold-down fingers. Lightly sprung to hold your thin sticks in place while you glue. Laser cut from birch plywood. Use with magnets (magnets sold separately).
|
Pack of two sets. These long fingers will hold light structures 1/8" off the board so tissue can evenly shrink warp free after steaming or doping tissue. Laser-cut from birch plywood. Use 6 1/4" x 0.100" magnets per pack,(magnets sold separately).
|
Pack of four hold-down fingers. Lightly sprung to hold your thin sticks in place while you glue. Laser cut from birch plywood. Use with magnets (magnets sold separately).
|
Pack of four 1/16" rib squares, 1" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of 4 3/32" rib squares, 1" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four 1/8" rib squares, 1" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four 1/16" rib squares, 2" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four 3/32" rib squares, 2" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four 1/8" rib squares, 2" slot height. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of four (two inside & two outside) 30/90/60 deg squares. Longer edge of square edges is 2". Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Pack of four (two inside & two outside) 45/90/45 deg squares. Square edges are 2" long. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Set of 8 double ended Dihedral angle jigs. (only 4 shown in photo). One deg. steps from 0 - 15 deg. angle. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Set of 2 keel support stands with 1/16" slot. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Can be used with carbon alignment rod.
|
Set of 2 keel support stands with 3/32" slot. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Can be used with carbon alignment rod.
|
Set of 2 keel support stands with 1/8" slot. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Can be used with carbon alignment rod.
|
Pack of two 5 1/4" tall squares. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Center hole fits carbon alignment rod. Can also be screwed to bench.
|
Pack of two 12" horizontal scales. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Pack of two 6" tall vertical scales. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Pair of wing/stabilizer support fixtures. Adjusts from 1" to 7" high, and angle tilts over the range of -7.5 to + 7.5 deg. Nylon bolts and wing nuts used to lock fixture after adjusting. For magnetic tables add 4 magnets to each fixture (not supplied).
|
Pack of six stair step supports, 2 off 1/8"-1", 2 off 1 1/8"-2" and 2 off 2 1/8"-3" tall, all with 1/8" steps. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Pair of stair step supports, 3 1/8" - 4" tall, with 1/8" steps. Laser cut from birch plywood. Use with or without magnets (magnets sold separately).
|
Pack of two 5 1/4" protractors,adjustable from vertical to 30 deg off vertical. Use for tapered fuselage sides. Laser cut from birch plywood. Use with or without magnets (magnets sold separately). Can also be screwed to bench.
|